> For the complete documentation index, see [llms.txt](https://help.sbtinstruments.com/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://help.sbtinstruments.com/getting-started/prepare-for-first-use.md).

# Prepare for first use

Deep clean, then run a QC test. About 25 minutes, before the first sample.

<figure><img src="https://4216107837-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FeYTtd7c0A325muFr5lMW%2Fuploads%2FxJ1CVeXsJiv1sC4uBSpY%2Fgetting-started-path-prepare-for-first-use.svg?alt=media" alt="Getting started: Unboxing and Installation are done. This page is Prepare for first use. Run a sample comes next."><figcaption></figcaption></figure>

First use always starts with a deep clean, followed by a QC test. The QC test also unlocks the new flow cell for measurements.

<figure><img src="https://4216107837-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FeYTtd7c0A325muFr5lMW%2Fuploads%2Frc7ADT4LatBDlYGD0fvB%2Ffirst-use-sequence.svg?alt=media" alt="Deep clean with a deep clean vial for 15 minutes. Then the QC test: clean with a disinfection vial, measure the QC vial, clean with the same disinfection vial, and measure a dilution vial as the blank. Two check marks mean BactoBox is ready for samples."><figcaption></figcaption></figure>

## Get things ready

All four come in the [Getting started bundle](https://help.sbtinstruments.com/item-register/consumables/getting-started-bundle.md).

* 1 × [deep clean vial](https://help.sbtinstruments.com/item-register/consumables/deep-clean-vial.md)
* 1 × [disinfection vial](https://help.sbtinstruments.com/item-register/consumables/disinfection-vial.md)
* 1 × [QC vial](https://help.sbtinstruments.com/item-register/consumables/qc-vials.md)
* 1 × [dilution vial](https://help.sbtinstruments.com/item-register/individual-items/dilution-vial.md)

## Deep clean for 15 minutes

Place the deep clean vial in the vial rack and move the tubing kit to it.

<figure><img src="https://4216107837-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FeYTtd7c0A325muFr5lMW%2Fuploads%2FwUiHhFPyPMnsv8Sc9ETN%2Fdeep-clean-vial-setup.svg?alt=media" alt="Three steps. Unscrew the cap of the deep clean vial and keep it for later. Place the open vial in one of the holes of the vial rack. Move the tubing kit to the vial. Its plug replaces the cap, and the steel tubes reach down into the liquid."><figcaption></figcaption></figure>

1. Press and hold <kbd>Measure</kbd> for 2 seconds, until the *Programs* menu appears.

   ![In a menu, each button does what the screen shows above it. Measure is OK, Stop is back, Empty is down and Clean is up.](https://4216107837-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FeYTtd7c0A325muFr5lMW%2Fuploads%2FxfmGysuT5ZLzHuBe6Aod%2Fbuttons-in-menus.svg?alt=media)
2. Use the navigation buttons (<kbd>∨</kbd> <kbd>∧</kbd>) to select *Deep clean*, and press <kbd>OK</kbd>.
3. Select *15 minutes* and press <kbd>OK</kbd> to start.

<figure><img src="https://4216107837-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FeYTtd7c0A325muFr5lMW%2Fuploads%2Fi8DD8cQUrnpO72yIT2Bj%2Fselect-deep-clean-duration.png?alt=media&#x26;token=df243571-3dfa-49b2-9c01-c631ab491b64" alt="Selecting 15 minutes in the Deep clean program"><figcaption></figcaption></figure>

When the program is done, close the deep clean vial with its screw cap. Discard it as biological waste.

## Run the QC test

{% stepper %}
{% step %}
**Get a QC vial**

Cut out one ready-made QC vial (QC07). Cut out only one at a time.

<figure><img src="https://4216107837-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FeYTtd7c0A325muFr5lMW%2Fuploads%2FL1sgllI6Ppzo7d756HVx%2FQC-RTU-cut.avif?alt=media" alt="Cutting one QC vial off the strip"><figcaption></figcaption></figure>

Using QC stock (QC04, QC05 or QC06)? [Make a QC vial from QC stock](https://help.sbtinstruments.com/maintenance/qc-test/make-qc-vial.md) first.
{% endstep %}

{% step %}
**Start the&#x20;*****QC test*****&#x20;program**

1. Press and hold <kbd>Measure</kbd> for 2 seconds, until the *Programs* menu appears.
2. Press <kbd>OK</kbd> to select *QC test*.
3. Set the target concentration with the buttons. On a ready-made QC vial, it is printed in the center of the sticker. For QC stock, it is on the certificate of analysis.

<figure><img src="https://4216107837-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FeYTtd7c0A325muFr5lMW%2Fuploads%2FQZPVBhkBgJ4wGonVsgcc%2FQC-RTU-set-concentration.avif?alt=media" alt="Setting the target concentration in the QC test program"><figcaption></figcaption></figure>
{% endstep %}

{% step %}
**Clean**

Move the tubing kit to the disinfection vial and press <kbd>OK</kbd>. If you just ran a [Clean](https://help.sbtinstruments.com/more/how-to-guides/clean-your-setup.md), BactoBox® skips this step.
{% endstep %}

{% step %}
**Measure the QC vial**

Shake the QC vial vigorously for 10 seconds, because the QC beads settle over time. Move the tubing kit to it and press <kbd>OK</kbd>. Press <kbd>OK</kbd> again to leave the result screen.

<figure><img src="https://4216107837-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FeYTtd7c0A325muFr5lMW%2Fuploads%2FZ3VkKhNruziF1kyAu2h5%2FRTU-QC-qc-vial.avif?alt=media" alt="Measuring the QC vial"><figcaption></figcaption></figure>
{% endstep %}

{% step %}
**Clean again**

Move the tubing kit back to the same disinfection vial and press <kbd>OK</kbd>. This rinses out the QC beads.

<figure><img src="https://4216107837-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FeYTtd7c0A325muFr5lMW%2Fuploads%2FhaiKxuAoufNhr9fxFzij%2FRTU-QC-clean2.avif?alt=media" alt="Cleaning with the disinfection vial"><figcaption></figcaption></figure>
{% endstep %}

{% step %}
**Measure the blank**

Move the tubing kit to the ready-made dilution vial, with nothing added, and press <kbd>OK</kbd>.

<figure><img src="https://4216107837-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FeYTtd7c0A325muFr5lMW%2Fuploads%2FsKzFrtMHi3cFIrmz51ML%2FRTU-QC-dilution-vial.avif?alt=media" alt="Measuring the dilution vial as the blank"><figcaption></figcaption></figure>
{% endstep %}

{% step %}
**Ready for samples**

Two check marks <i class="fa-check-double">:check-double:</i> on the screen mean the QC test passed. BactoBox® is ready for samples.

Discard the QC vial and the dilution vial. Both are for single use. Keep the disinfection vial for the Clean after each sample.
{% endstep %}
{% endstepper %}

{% hint style="danger" %}

#### Did the QC test fail?

The program goes back one step, so you can repeat it with a fresh vial.

Blank failed with code 5010 or 5011? See [Blank fails](https://help.sbtinstruments.com/troubleshooting/error-code-on-screen/qc-test-fails/blank-fails.md). For other codes, see [QC test fails](https://help.sbtinstruments.com/troubleshooting/error-code-on-screen/qc-test-fails.md).
{% endhint %}

Next: [Before you measure](https://help.sbtinstruments.com/everyday-use/before-you-measure.md).


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation by asking a question.

Perform an HTTP GET request on the following URL with the `ask` and `goal` query parameters:

```
GET https://help.sbtinstruments.com/getting-started/prepare-for-first-use.md?ask=<question>&goal=<user_goal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is what the user is ultimately trying to achieve, the reason they need the answer. Sharing it helps GitBook give you a better, more relevant answer. A goal is most helpful when it describes the outcome the user wants rather than restating the question. For example, with `ask=how do I create an API token`, a goal like `automate deployments from our CI pipeline` lets GitBook tailor the answer to that use case.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.
